欢迎访问:山东燊赫通风设备有限公司!
一键分享网站到:
服务热线
0531--68856675
网站首页
公司简介
荣誉资质
新闻中心
产品中心
工程案例
留言反馈
联系我们

新闻中心

当前位置: 首页-新闻中心 > 新风通风管道加工时切割面的选取

新风通风管道加工时切割面的选取

发布时间:2017/09/04

  山东通风管道加工运行时,由部分新风与部分室内回风混合后的空气,在室内机组中经过净化、湿调、冷却或加热处理后,通过送风管送至各个房间中,再由回风管将室内空气集中送回室内机组。整个系统的运行由一个温控器来自动控制设备的启停和保持室内恒温。

  The processing operation of Shandong ventilation duct, in part by the fresh air and return air mixing part of indoor air after, after cleaning, conditioning, cooling or heating treatment in the indoor unit, the air supply pipe to send to each room, the indoor air concentration to indoor units from the air return pipe. The whole system is operated by a thermostat to automatically control the start and stop of the equipment and maintain the indoor constant temperature.

  新风从空气较洁净区域进入,由污浊处排出。一般污浊空气从浴室、卫生间及厨房排出,而新鲜空气则从起居室、卧室等区域送入。

  Fresh air enters from the clean air area and is expelled from the polluted area. General dirty air from the bathroom, bathroom and kitchen, while the fresh air from the living room, bedroom and other areas into.

  通风管道加工要注意细节方面,只有注重细节才能确保风管在使用中不出现问题。

  Attention should be paid to the details of ventilation duct processing. Only by paying attention to detail can the air duct be free from any problems during use.

  1.清洁板材切割面的粉末、油渍、水渍、灰尘,用毛刷在切割面上涂刷胶粘剂.

  1. clean the cutting surface, powder, grease, water stain and dust, and brush the adhesive on the cutting surface

  2.板材接缝处从一端至另一端按对中位置粘上压敏铝箔胶带,压敏胶带粘在一边的宽度不小于20mm.
油烟净化器

  2. the plate joint from one end to the other end, press the middle position of the pressure sensitive aluminum foil tape, the pressure sensitive adhesive tape on the side of the width of not less than 20mm.

  3.将风管面板按设计要求粘合,待涂胶不粘手时.并用刮板压平.对难以刮平的局部,可用木锤轻轻锤平.

  3., the wind tube panel according to the design requirements of bonding, to glue do not stick hand. And use scraper leveling. For difficult to flat parts, can use wood hammer gently hammer flat

  4.清洁板材切割面的粉末,按空调风管加工任务单检查风管面板是否符合设计要求.

  4. cleaning panel cutting powder, according to the air conditioning duct processing task list, check whether the wind pipe panel meets the design requirements

  5.检查板材接缝粘接是否达到质量规.

  5. check whether the bonding of plates meets the quality requirements

  中央空调通风管道可采用地板送风或天花板送风,除了可调节温度,还可通过将增湿器和温度调节器一起工作来调节空气湿度。其还具备自动新风系统,可把室外的新鲜空气以每小时6次的频率为室内进行一次更换。

  The central air conditioning ventilation pipe can be underfloor or ceiling fan, in addition to adjust the temperature, but also through the humidifier and the temperature regulator working together to regulate the air humidity. It also has automatic fresh air system, outdoor fresh air can be replaced at 6 times per hour for indoor replacement.

  本文由山东通风管道加工为您提供,我们的网站是:http://www.jnqsg.com/我们将以全心全意的热情为您提供更优质的服务,欢迎您的访问!

  This article is provided by the Shandong ventilation pipe processing, our website is: http://www.jnqsg.com/ We will wholeheartedly provide you with better service, you are welcome to visit!

网站首页 公司简介 荣誉资质 新闻中心 产品中心 工程案例 留言反馈 联系我们
contact us联系我们
地址:济南市天桥区
电话:0531--68856675
QR code关注我们
二维码拿出手机扫一扫

本站图片均由网站所有方提供,部分图片来源于网络,如有任何疑问请第一时间与我们联系,未经沟通本站不承担相关法律责任!

立即咨询 立即咨询 立即咨询