您好,欢迎访问山东燊赫通风设备有限公司网站!

服务热线

13210558111

镀锌钢通风管道加工粘合要求

来源:http://www.jnqsg.com/     发布时间:2017-09-21  

  山东通风管道加工要注意细节方面,只有注重细节才能确保风管在使用中不出现问题。

  Attention should be paid to the details of ventilation duct processing. Only by paying attention to detail can the air duct be free from any problems during use.

  1.清洁板材切割面的粉末、油渍、水渍、灰尘,用毛刷在切割面上涂刷胶粘剂.

  1. clean the cutting surface, powder, grease, water stain and dust, and brush the adhesive on the cutting surface

  2.将风管面板按设计要求粘合,待涂胶不粘手时.并用刮板压平.对难以刮平的局部,可用木锤轻轻锤平.

  2., the wind tube panel according to the design requirements of bonding, to glue do not stick hand. And use scraper leveling. For difficult to flat parts, can use wood hammer gently hammer flat

  3.板材接缝处从一端另一端按对中位置粘上压敏铝箔胶带,压敏胶带粘在一边的宽度不小于20mm.

  3. the plate joint from one end to the other end, press the middle position of the pressure sensitive aluminum foil tape, the pressure sensitive adhesive tape on the side of the width of not less than 20mm.

  4.清洁板材切割面的粉末,按空调风管加工任务单检查风管面板是否符合设计要求.

  4. cleaning panel cutting powder, according to the air conditioning duct processing task list, check whether the wind pipe panel meets the design requirements
山东通风管道加工

  5.检查板材接缝粘接是否达到质量规.

  5. check whether the bonding of plates meets the quality requirements

  6、镀锌钢钣风管是目前空调工程、通风排烟系统中应用传统、广泛的产品。镀锌钢钣风管内壁光滑、阻力小、气密性好、承压强度高。钢板风管现场制做方便,与土建工程配合紧密,能适合非常复杂的通风工程。

  6, galvanized steel sheet wind pipe is the air conditioning, ventilation and smoke exhaust system in the application of the most traditional and most widely used products. Galvanized steel sheet air pipe inner wall is smooth, small resistance, good air tightness, high bearing strength. The steel pipe is easy to be made on the spot and is closely matched with the civil engineering, so it can be applied to the very complicated ventilation project.

  7、镀锌钢板风管造价比不锈钢板风管要低,用途十分广泛。目前镀锌钢钣风管广泛应用于各种通风、空调系统中。通风风管分圆型和矩形两种,可根据广大用户的不同需要生产各种型状、各种规格型号的风管。

  7, galvanized steel pipe duct cost than stainless steel plate, duct is low, use is very extensive. The galvanized steel sheet air pipe is widely used in all kinds of ventilation and air conditioning system. The ventilation duct is divided into two types: round type and rectangular type. It can produce all kinds of pipes of various shapes and sizes according to the different needs of the general users.

  8、不锈钢板风管防腐蚀能力强,内壁光滑,同等厚度的不锈钢板风管的承压能力和硬度均大于镀锌板风管。不锈钢管的光洁度很好,易于清洁,外观高档。但造价也较高。

  8 、 stainless steel plate, wind pipe corrosion resistance is strong, the inner wall is smooth, the same thickness of stainless steel plate, the pressure bearing capacity and hardness of the air duct is larger than the galvanized pipe duct. Stainless steel pipe has a good finish, easy to clean, high appearance. But the cost is higher.

  9、共板式法兰风管又称无法兰风管,其制作形式比传统的矩形风管加工速度更快捷、更方便、更小的漏风率。其优点是节省材料,减少工程投资;漏风量小,降低能耗,节省运行费用,颇受施工企业欢迎。

  9, the common plate flange duct, also known as "unable to LAN pipe", its production form than the traditional rectangular wind pipe processing faster, more convenient, smaller leakage rate. The utility model has the advantages of saving material, reducing engineering investment, small air leakage, reducing energy consumption and saving operating cost, and is well received by construction enterprises.

  本文由山东通风管道加工为您提供,我们的网站是:http://www.jnqsg.com/我们将以全心全意的热情为您提供更的服务,欢迎您的访问!

  This article by the Shandong ventilation pipe processing provides for you, our website is: http://www.jnqsg.com/, we will wholeheartedly wholeheartedly provide you with better service, you are welcome to visit!

上一篇:烟罩式一体式油烟净化器的资源配置
下一篇:通风管道阀门启闭方向的开启度