欢迎访问:山东燊赫通风设备有限公司!
一键分享网站到:
服务热线
0531--68856675
网站首页
公司简介
荣誉资质
新闻中心
产品中心
工程案例
留言反馈
联系我们

新闻中心

当前位置: 首页-新闻中心 > 消防通风与防排烟工程

消防通风与防排烟工程

发布时间:2017/12/20

  玻璃钢风管的安装施工工艺是本工程的重点。无机玻璃钢风管在近几年被广泛使用,随着玻璃钢风管制造技术的日益完善,以及在大型工程中的应用,工程施工人员已经能够掌握这种成熟的施工工艺。而本工程玻玻璃钢风管应用量较大,安装要求高,故作为本工程通风空调系统施工中的重点和难点。
  The installation and construction technology of FRP wind pipe is the key point of this project. Inorganic glass fiber reinforced plastic wind pipe has been widely used in recent years. With the improvement of manufacturing technology and the application in large-scale engineering, construction workers have been able to master this mature construction technology. In this project, the glass glass steel wind pipe has a large amount of application and high installation requirements, so it is the key and difficult point in the construction of the ventilation and air conditioning system in this project.
  通风机(含排烟机)的安装
  The installation of a ventilator (including a smoke exhauster)
  1)整体安装的风机,搬运和吊装的绳索不得捆缚在转子和机壳或轴承盖的吊环上。
  1) whole fan installed, carrying and lifting rope shall be bound in the rotor and the shell rings or the bearing cover.
  2)通风机的进风管、出风管等装置应有单独的支撑,并与基础或其它建筑物连接牢固;风管与风机连接时,不得强迫对口,机组不应承受其它机件的重量。通风机传动装置的外露部位以及直通大气的进、出口,必须装设防护罩(网)或采取其它安全措施。
  2) the inlet and outlet pipes of fans should have independent support and are firmly connected with foundations or other buildings. When air pipes are connected with fans, they must not be forced to match counterparts, and the crew should not be able to bear the weight of other parts. The outgoing parts of the ventilator transmission and the inlet and outlet of the direct air must be equipped with a protective shield (net) or other safety measures.
  3)落地安装的离心风机:其基础应平整,通过调整减振器的位置,使各减振器受力及变形尺寸一致。
  3) a centrifugal fan installed on the ground: its foundation should be flat, and by adjusting the position of the damper, the size of the force and deformation of each damper is consistent.
  4)悬吊式轴流类风机安装:风机加设钢板连接板及型钢挑梁,使各个减振器受力及变形尺寸一致。
  4) installation of suspension type axial flow fan: the fan is equipped with steel plate connecting plate and type steel pick beam, so that the size of each damper is in accordance with the force and deformation size.
网站首页 公司简介 荣誉资质 新闻中心 产品中心 工程案例 留言反馈 联系我们
contact us联系我们
地址:济南市天桥区
电话:0531--68856675
QR code关注我们
二维码拿出手机扫一扫

本站图片均由网站所有方提供,部分图片来源于网络,如有任何疑问请第一时间与我们联系,未经沟通本站不承担相关法律责任!

立即咨询 立即咨询 立即咨询