通风管道是通风与空调系统的主要元件，由于很多原因风管加工设备会导致通风管道加工时出现很多问题，
山东通风管道加工厂家给大家给大家汇总了一下，比如以下问题：
The air duct is the main component of the ventilation and air conditioning system. For many reasons, the air duct processing equipment will cause many problems during the processing of the air duct. The Shandong air duct processing manufacturer summarized the following problems for you:
处理数据不符合标准
Processing data does not meet the standard
原因：数据不合格，每一步制造风管的要求不严格。
Cause: The data is unqualified, and the requirements for each step of air duct manufacturing are not strict.
步骤：在使用济南通风管道加工设备制造风管之前，需要对出厂合格证、数据质量确认等表面厚度等数据进行反思。以确保数据可用。
Step: Before using Jinan air duct processing equipment to manufacture air duct, it is necessary to reflect on the surface thickness and other data such as factory certificate and data quality confirmation. To ensure that data is available.
板外不平整，厚度不均匀，有明显的压痕、裂纹、锈蚀等环境;风道三维下沉，前端向外突出，变形明显。
The outside of the plate is not flat, the thickness is uneven, and there are obvious indentation, cracks, rust and other environments; The air duct sinks in three dimensions, and the front end protrudes outward with obvious deformation.
影响：运行中风管泄漏，空调负荷增加，影响风的寿命和性能。
Impact: The air duct leaks during operation, and the air conditioning load increases, affecting the life and performance of the wind.
禁止风管翘角和弯头
No air duct warping angle and elbow
原因：当板被布置和布置时，空气导管成对平行，并且相对的板在长度和宽度上不相等。
Cause: When the plates are arranged and arranged, the air ducts are parallel in pairs, and the relative plates are not equal in length and width.
步骤：打开下料时，应接好板材的边角，检查每张板材的长度、宽度和对角线，使其误差在允许范围内;下料后，与风管相对的两块板材应重叠，以检查尺寸精度。
Steps: When opening blanking, the edges and corners of the sheet shall be connected, and the length, width and diagonal of each sheet shall be checked to make its error within the allowable range; After blanking, the two plates opposite to the air duct shall overlap to check the dimensional accuracy.
表示两对矩形风道是三维的，两个端面不平行;折叠角度不直;对角线不平等;咬的不严格。
It indicates that two pairs of rectangular air ducts are three-dimensional, and the two end faces are not parallel; Folding angle is not straight; Diagonal inequality; The bite is not strict.
影响：会造成风管连接受力不均匀，安装后风管不均匀，法兰垫片松动，系统漏气，造成空调负荷损失，延长使用寿命。
Impact: It will cause uneven force on the air duct connection, uneven air duct after installation, loose flange gasket, and air leakage of the system, resulting in air conditioning load loss and extended service life.
The ventilation duct is applicable to the installation of central air conditioning ventilation ducts in industrial production and various engineering buildings. It is widely used in food industry, mechanical equipment manufacturing, pharmaceutical products, electronic industry, etc. You can come to us if you need http://www.jnqsg.com Consult!
上一篇：酒店厨房排烟罩的安装标准
下一篇：通风管道加工可能会存在两个质量问题
